Trempe et Revenu par Induction

L’équipe Ambrell spécialisée dans le durcissement se propose d’évaluer vos procédés et méthodologies actuels, puis de concevoir une solution de traitement thermique par induction daptée à vos procédés de trempe, de recuit et de revenu, en vous recommandant l’équipement, les outils et le système d’automatisation appropriés à vos besoins.

Contactez-nous

Trempe et Revenu par Induction

L’équipe Ambrell spécialisée dans le durcissement se propose d’évaluer vos procédés et méthodologies actuels, puis de concevoir une solution de traitement thermique par induction daptée à vos procédés de trempe, de recuit et de revenu, en vous recommandant l’équipement, les outils et le système d’automatisation appropriés à vos besoins.

Contactez-nous

Nous sommes là pour vous aider. Il existe deux types généraux de processus de durcissement : le durcissement continu traite la pièce complète alors que le durcissement superficiel traite en général la surface de la pièce et une partie de l'intérieur, en fonction de la profondeur des exigences de durcissement pour une application spécifique.

trempe Notes d'application

Cliquez pour lire comment le trempe par induction peut améliorer l'efficacité et la sécurité de votre processus de chauffage.

Pour rechercher toutes les notes trempe, Ctrl+F keyword ou ⌘+F keyword ou faites défiler.


Hardening surgical blades Hardening surgical blades

To quickly heat a steel surgical blade to 2000°F (1093°C) within 2 seconds so as to harden the blade edge.

Hardening Seat Belt PartsHardening Seat Belt Parts

A four-turn helical concentrating coil is specially designed to deliver uniform heat to the steel seat belt retraction gear.

Hardening the teeth of a large saw bladeHardening the teeth of a large saw blade

A torch isn't as precise as induction nor is it repeatable; induction heating is highly repeatable, uses less energy than a torch and offers instant on/off heating

Case hardening a steel fitting (machined parts manufacturer)Case hardening a steel fitting (machined parts manufacturer)

The coil design enabled the part to be raised into the heating coilfrom the bottom. The design was also made to ensure it will work well within the customer's current setup...

Surface hardening of steel screwsSurface hardening of steel screws

Induction heating enables precise application of heat, faster process time and production rates and the ability to be incorporated into existing production lines

Hardening teeth on a steel motorcycle gearHardening teeth on a steel motorcycle gear

A single turn helical coil is used to heat the gear. The gear is placed on a spindle and rotated at 300-350 RPM's.

Hardening steel screw threadsHardening steel screw threads

A five turn helical coil is used heat the screw threads. The screw is placed in the coil, heat is applied for 8 seconds to achieve a 2 long zone at the required hardness.

Hardening the end of steel hand-held marking stampsHardening the end of steel hand-held marking stamps

To harden various size ends of hand held marking stamps. The area to be hardened is 3/4 (19mm) up the shank.

Hardening of Steel Cam AssemblyHardening of Steel Cam Assembly

Hardening the cam outer surfaces with induction results in uniform heating for uniform results, one coil can be used for many geometries, consistent results from piece to piece

Case Hardening of Armature ShaftCase Hardening of Armature Shaft

A five turn helical coil is used to heat the gear end of the shaft to 1700°F

Hardening Cast Iron PulleysHardening Cast Iron Pulleys

Heat cast iron pulleys to 1600°F(871.1°C) in order to achieve a hardness of 55 Rockwell C.

Hardening Stainless Steel Surgical Knife BladesHardening Stainless Steel Surgical Knife Blades

A two turn helical coil with an internal quartz tube designed to scan the length of the blade is used to heat the blade to 1850°F (1010°C) to achieve the desired hardness.

Hardening Bed Knife Blade for Reel Type Lawn MowersHardening Bed Knife Blade for Reel Type Lawn Mowers

The hardness desired is between 45 to 55 Rockwell C, and should be measured 0.062in (1.6mm) from the cutting edge.

Note de trempe populaire

Vidéo de trempe Populaire

Chauffage par induction

Il est une méthode rapide, efficace, précise et répétable, sans contact permettant de chauffer les métaux ou les autres matériaux conducteurs d'électricité. Le matériau peut être un métal comme de l'acier, du cuivre, de l'aluminium, du laiton ou cela peut être un semi-conducteur comme du carbone, du graphite ou du carbure de silicium. Pour chauffer les matériaux non conducteurs comme le plastique ou le verre, l'induction est utilisée pour chauffer un suscepteur conducteur d'électricité, habituellement le graphite, qui transfère ensuite la chaleur du matériau non conducteur.

Lisez notre brochure de quatre pages "À propos du chauffage par induction"

Lire la Brochure

Brochure: À propos du chauffage par induction

Bobines d'Induction

La bobine d’induction, ou inducteur, est le composant du système de chauffage par induction qui détermine l’efficacité et le rendement du chauffage de la pièce.

La bobine sert à transférer l’énergie de l’alimentation en puissance et de la tête d’induction à la pièce, en créant un champ électromagnétique alternatif.

Lire la Brochure

Brochure: Bobines d'Induction

Quatre Façons de Contacter Ambrell Pour Obtenir de L'aide

AMBRELL CORPORATION

1655 Lyell Avenue
Rochester, NY 14606
United States
 

Directions to Ambrell Corporation Directions

T: +1 585 889 9000

F: +1 585 889 4030

Contact Sales

Contact Orders

Contact Service

AMBRELL B.V.

Holtersweg 1
7556 BS Hengelo
The Netherlands
 

Directions to Ambrell B. V. Directions

T: +31 880 150 100

F: +31 546 788 154

Contact Sales

Contact Orders

Contact Service

AMBRELL Ltd.

Unit 6, Space Business Centre
Tewkesbury Road
Cheltenham, GLOS, GL51 9FL
United Kingdom

Directions to Ambrell Ltd.Directions

T: +44 1242 514 042

F: +31 546 788 154

Contact Sales

Contact Orders

Contact Service